View U490B_62733.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

U490B
One-Shot Phase Control
Description
The monolithic integrated bipolar circuit, U490B, is a one-shot power control circuit, designed to control the thyristor which is mainly used in electric stapler devices. The IC is preferred to realise a one-shot phase control, where any phase angle and thus any intensity of the load voltage is adjustable. After successful triggering and the following delay time, an ignition pulse at the output is released. A further triggering is only possible after the elapse of the delay time.
Features
D D D D D
L D1 1N4007 R1 Vmains 230 VX C1 47 mF/ 10 V N 8 VS 3 24 kW/ 2W R3 220 kW C3 1.5 nF
Applications
D Electric stapler devices
Phase controlled thyristor ignition Triggering with time delay Repetition time delay Supply current
x2 mA
Package: DIP8, SO8
Mains supply via resistor
S1
95 10866
4 GND
Start delay Supply stage Sync. Repetition delay Trigger control
2 C2 47 nF
R2 220 kW
Load
D2
Phase control
POR Control input 5 R5 47 kW C6 150 nF Output stage Ramp 6
7 R7 33 W C7 22 nF
R4 220 W C4 47 nF/ 250 VX
C5 150 nF
[68 kW
Figure 1. Block diagram with external circuit
TELEFUNKEN Semiconductors Rev. A1, 29-May-96
1 (6)
U490B
Pin Description
NC 1 Trigger 2 8 VS 7 Output 6 Ramp 5 Contr Pin 1 2 3 4 5 6 7 8 Symbol NC Trigger Sync. GND Contr Ramp Output VS Function Not connected Triggering Synchronization Ground Control input Ramp Output Supply voltage
Sync. 3 GND 4
Supply, Pin 8
Internal voltage limiter enables a simple supply from the mains via series resistor R1.The supply voltage between Pin 8 (VS) and ground (Pin 4) builts up via R1 and is smoothed by the capacitor C1. Series resistor R1 can be calculated as follows: R 1max
The circuit is released, when four periods of the line voltage have expired after build up of the operating voltage, before the switch S1 is closed.
[ 0.85 x V 2 x- IV where + Mains supply voltage V + Maximum supply voltage V I + I )I I + Maximum current consumption of the IC + Current consumption of the I
mains Smax tot
S1 closed
mains Smax
tot Smax X
Smax
X
V3 (Sync.)
open V8
external components
V8 V2 (Trigger)
Phase Control, Pins 3, 5 and 6
The circuit is synchronized with mains supply through Pin 3. As long as the switch S1 is open, the circuit is in wait state i.e., the capacitor C6 (150 nF) is discharged and is kept in this state (High level). When the switch S1 is closed, there is a current flow in Pin 2 which is evaluated by the circuit. If this current flows after the elapse of delay time, then the phase control is released. Capacitor, C6, is 100 mA towards ground. At the then charged with I6 same time, there is a current flow of 100 mA into Pin 5, which results in voltage drop across resistor R5. Control voltage, V5, is then 1.5 V lower internally.
V6 (Ramp) "X"
V7 (Output)
+
0
50 ms
[
100 ms t1
150 ms t
200 ms "X"
V6 V5 - 1.5 V 150 mV
[
The output stage is released when the ramp voltage V6 is equal to (V5 1.5 V). When the voltage difference is 150 mV, it is again turned-off.
V7
95 10867
*
The result is an output pulse, whose phase shift to the zero crossing of mains voltage is determined by the resistor R5 at control input Pin 5 (see fig. 2). Capacitor C6 is charged to a value of 1.5 V. It remains there till the switch S1 again opens and the repetition delay time is over.
tp
t
[
Figure 2. Signal characteristics
2 (6)
TELEFUNKEN Semiconductors Rev. A1, 29-May-96
U490B
Absolute Maximum Ratings
Reference point Pin 4 (GND), unless otherwise specified Parameters Supply current t Output stage Input voltage Input current t Pin 8 Symbol IS is Value 30 150 - 0.5 V to VS 5 30 0 V to V8 +125 - 10 to +100 - 40 to +125 Unit mA
v 10 ms v 1 ms
Pin 7 Pin 2, 3 Pin 5, 6
"I
VI
I
mA
C C C
Input voltage Junction temperature Ambient temperature Storage temperature range
VI Tj Tamb Tstg
Thermal Resistance
Parameters Junction ambient DIP8 SO8 on p.c. SO8 on ceramic Symbol RthJA Value 110 220 140 Unit K/W
Electrical Characteristics
VS
+ 7 V, T
amb
= 25C, reference point Pin 4 (GND), unless otherwise specified Test Conditions / Pins IS 3 mA Pin 8 IS 30 mA VS 7 V Pin 8 Pin 8
Parameters Supply voltage limitation Current consumption Voltage monitoring Switch-on threshold Switch-off threshold Synchronization Voltage limitation Switch-on threshold Switch-off threshold Trigger input Voltage limitation Switch-on threshold Switch-off threshold Start delay time Repetition delay time
+ + +
Symbol VS IS VSon VSoff
Min. 7.2 7.4
Typ. 8.2 8.4
Max. 9.2 9.4 2
Unit V mA V
5 3 1.5 0.75 120 35 1.5 0.75 120 35 40 60 60 80
I3 I3
+1 mA + -1 mA +1 mA + -1 mA + 50 Hz
Pin 3 Pin 3 - 8 Pin 3 Pin 2 Pin 2 - 8 Pin 2
Vlim -Vlim ITon IToff Vlim -Vlim ITon IToff t1 t2
V
mA
I2 I2
V
mA
ms
fmains
Pin 2-7
TELEFUNKEN Semiconductors Rev. A1, 29-May-96
3 (6)
U490B
Parameters Phase control Control input: Input voltage range Input current Ramp Charge current Discharge current Phase shift Test Conditions / Pins Pin 5, 6, 3 Pin 5 2V 2V U5
6
Symbol
Min.
Typ.
Max.
Unit
v V5 v V8 v V6 v
Pin 6 V8 - 0.5 V Pin 7-5 V5
VI II Ich -Idis
2 50 50 2
90 90
VS 130 130
mA mA
mA
V
+4V C + 150 nF
Status OFF Status ON C6
Output stage, V7 0 V Output reverse current Output current Pulse width
+
V5 Pin 7
+2V +V
8
tdmax tdmin
7 600 10 100 100 200 300
ms
ms mA
mA
"I
+150 nF, see figure 2
o(r) -Io
tp
ms
4 (6)
TELEFUNKEN Semiconductors Rev. A1, 29-May-96
U490B
Dimensions in mm
Package: DIP8
94 8873
Package: SO8
94 8862
TELEFUNKEN Semiconductors Rev. A1, 29-May-96
5 (6)
U490B
Ozone Depleting Substances Policy Statement
It is the policy of TEMIC TELEFUNKEN microelectronic GmbH to 1. Meet all present and future national and international statutory requirements. 2. Regularly and continuously improve the performance of our products, processes, distribution and operating systems with respect to their impact on the health and safety of our employees and the public, as well as their impact on the environment. It is particular concern to control or eliminate releases of those substances into the atmosphere which are known as ozone depleting substances ( ODSs). The Montreal Protocol ( 1987) and its London Amendments ( 1990) intend to severely restrict the use of ODSs and forbid their use within the next ten years. Various national and international initiatives are pressing for an earlier ban on these substances. TEMIC TELEFUNKEN microelectronic GmbH semiconductor division has been able to use its policy of continuous improvements to eliminate the use of ODSs listed in the following documents. 1. Annex A, B and list of transitional substances of the Montreal Protocol and the London Amendments respectively 2 . Class I and II ozone depleting substances in the Clean Air Act Amendments of 1990 by the Environmental Protection Agency ( EPA) in the USA 3. Council Decision 88/540/EEC and 91/690/EEC Annex A, B and C ( transitional substances ) respectively. TEMIC can certify that our semiconductors are not manufactured with ozone depleting substances and do not contain such substances.
We reserve the right to make changes to improve technical design and may do so without further notice. Parameters can vary in different applications. All operating parameters must be validated for each customer application by the customer. Should the buyer use TEMIC products for any unintended or unauthorized application, the buyer shall indemnify TEMIC against all claims, costs, damages, and expenses, arising out of, directly or indirectly, any claim of personal damage, injury or death associated with such unintended or unauthorized use. TEMIC TELEFUNKEN microelectronic GmbH, P.O.B. 3535, D-74025 Heilbronn, Germany Telephone: 49 ( 0 ) 7131 67 2831, Fax number: 49 ( 0 ) 7131 67 2423
6 (6)
TELEFUNKEN Semiconductors Rev. A1, 29-May-96

▲Up To Search▲

Price & Availability of U490B

	To Download U490B Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .